WELCOME TO RIVER DAVES PLACE

Search results

  1. TEAGUE CUSTOM MARINE

    SOLD - Mercury 900SC Replica For Sale

    SOLD.... Mercury 900SC Replica For SALE! $22,000 OBO This is a low hour Mercury Racing 900SC replica. All parts were purchased from Mercury to build the engine. Freshwater use only. This is a takeout engine; not built at TCM. Engine is a 572 cubic inch, solid roller cam, with Crower crank and...
  2. TEAGUE CUSTOM MARINE

    Schiada 21RC TT Vdrive

    5 hours run time. 10 minutes above 5000 rpm. 478 hours in front of fox?s. Extremely clean boat. Been in, up, and around every inch of it. Had all the right people contribute to the build and it is a nice piece. GLWS JT
  3. TEAGUE CUSTOM MARINE

    SCOPE Poker Run Catalina 2017!

    You are playing with fire JT
  4. TEAGUE CUSTOM MARINE

    The Hamlett Project

    No problem! We have new stainless hardline dipstick tubes too [emoji106]
  5. TEAGUE CUSTOM MARINE

    The Hamlett Project

    That's a 10 quart :) JT
  6. TEAGUE CUSTOM MARINE

    How much water pressure

    Teague motors read pressure at top of intake/therm housing before water goes to the headers. Merc motors read just after the water pump, usually before the first oil cooler. You'll see a lot more pressure at the merc location, approximately double. However if there is a blockage anywhere in...
  7. TEAGUE CUSTOM MARINE

    New build Eliminator 27 Speedster

    Looked good at big cat! JT
  8. TEAGUE CUSTOM MARINE

    Sterndrive lower blueprint

    Stewart motor sports in havasu or Wilson in Florida are the people who make them work. JT
  9. TEAGUE CUSTOM MARINE

    HP575 in 28 Howard Bullet

    No problem! The usual suspects in havasu can help. Barrett, Robbie at Nordic, Prestige.
  10. TEAGUE CUSTOM MARINE

    HP575 in 28 Howard Bullet

    Chris already knew all that, he just didn't feel like typing it :)
  11. TEAGUE CUSTOM MARINE

    HP575 in 28 Howard Bullet

    Make sure the fuel pressure is properly vacuum referencing. It is connected between the throttle bodies and supercharger. These injectors are very sensitive to pressure. Without a proper vacuum reference, too much pressure at idle and cruise=fat. You can check at Schrader valve on TB. 32 psi...
  12. TEAGUE CUSTOM MARINE

    Cost of whipple installed on a 525 ?

    That's pretty accurate. I can look up the last two we did for real numbers, but every application has its own variations. There are upgrade options, most notably a dual stage Latham water pump we have configured for the gen 6 serp drive. There is a lot more to it than just opening the box and...
  13. TEAGUE CUSTOM MARINE

    Article: Teague Set to Co-host Krusin' for Kids 2017 - the Kickoff to Desert Storm

    You can view the page at http://www.riverdavesplace.com/forums/content.php?753-Teague-Set-to-Co-host-Krusin-for-Kids-2017-the-Kickoff-to-Desert-Storm
  14. Teague Set to Co-host Krusin' for Kids 2017 - the Kickoff to Desert Storm

    Teague Set to Co-host Krusin' for Kids 2017 - the Kickoff to Desert Storm

    Teague Custom Marine is thrilled to be co-hosting the 6th Annual Krusin' for Kids event at DESERT STORM 2017, with Lake Racer LLC and other sponsors! Those that have been part of Krusin' for Kids know that this day is very special and made possible by our volunteer boaters, helpers and the...
  15. TEAGUE CUSTOM MARINE

    Ilmor MV-10 625 Viper Complete Engine

    Mid 90's It would work in a 25. Just took a deposit on the engine.
  16. TEAGUE CUSTOM MARINE

    Ilmor MV-10 625 Viper Complete Engine

    Buyer cancelled. Wife killed the deal! $19,000 OBO
  17. TEAGUE CUSTOM MARINE

    Ilmor MV-10 625 Viper Complete Engine

    For sale: $19,000 OBO Ilmor MV-10 625 Viper Complete engine. Gloss red paint. Currently installed in a 27 Daytona (original engine) with 180 on the boat hour meter (usually translates to about 160 ECM run hours) Maintained at Teague Custom Marine. Leak down and header check, along with major...
Top