RZR4

[LowRiver2]

Picked up a RZR4 a month ago and it went straight to SDR
Cage:1 3/4"/opening doors
Twisted Stitch Vortex seats-(heated fronts)/rear bench
Crow 3" 5 points on 4, 2" 4point on center rear bench
ITP 7's/OMF beadlocks
Rigid 30" LED on roof
Rigid 10" LED on front push bar
HID hi low kit on headlights
Center mirror
LED dome light
UMP air canister
Next up: Clutch kit and paddles for Mother G

 

[djunkie]

Now that's pretty bad ass. I like the cage.

 

[LowRiver2]

Lights work great

 

[djunkie]

Lights work great

I got a 40" LED light bar on my rhino and it's bright as hell.

 

[LowRiver2]

Doors make for easy entry
My buddy built one at same time, he did HID's for desert, and matte black on cage vs. gloss for me. Both did great on the Poker run

 

[LowRiver2]

Poker run:

 

[LowRiver2]

The lock and ride box/gas can holder is nice, got an 18 pack AO cooler to fit in the second gas can holder

 

[LowRiver2]

Looks even better dirty!

 

[LowRiver2]

Suspension was much better than expected, takes whoops 10X better than my former rhino with bilsteins. Power was good, plenty of top end for this suspension, and no bucking like the rhino, even with 3 200+lb. guys.

 

[Wmc]

It look real nice last weekend on the Ca side.

 

[jesco]

Looks awesome. My buddy had his cage done by SDR, they make a great cage. I really want one of these but they are just a little small in the leg room department in the front seats, Im 6'4". Did changing the seats to TS give you anymore leg room? I was wondering if there was any way to move the pedals forward 2 or 3 inches, fab new mounts or something.

 

[LowRiver2]

A little more room but not much, I"m 6'2" and if it was'nt for the notched out section of floor in front of the gas pedal(standard), I'd have my knee on the dash.

It would be easy to cut off the left side of the center dash (has 1" overlap) and SDR or a dremel could do it quick and clean. That would most likely do it for you.

The TS seat drops a little but Tim at SDR is planning on doing a lowered seat base like he does for the rhino in the near future. The wrap around support of the TS seat is a definate improvement.

 

[pronstar]

Looks awesome. Tim does great work :thumbsup

 

[jesco]

A little more room but not much, I"m 6'2" and if it was'nt for the notched out section of floor in front of the gas pedal(standard), I'd have my knee on the dash.

It would be easy to cut off the left side of the center dash (has 1" overlap) and SDR or a dremel could do it quick and clean. That would most likely do it for you.

The TS seat drops a little but Tim at SDR is planning on doing a lowered seat base like he does for the rhino in the near future. The wrap around support of the TS seat is a definate improvement.

Yeah I know what you mean with the little notch, I would be really screwed if that were not there. That notch is the only thing that makes me still consider buying one, just afraid I will get uncomfortable on long rides. I was thinking there might be something that could be cut or moved a little to get a little extra room, dont need much. Thanks for the info, I will have to revisit a RZR dealer soon and look into it more. Car turned out really nice, SDR has that cage/door combo nailed, cleanest on the market I think.

 

[Cole Trickle]

Bad ass 4...

I would love to have one but the idea of loosing my ass on the rhino and starting over on a build would make my bank account cry...lol

 

[LowRiver2]

I

would love to have one but the idea of loosing my ass on the rhino and starting over on a build would make my bank account cry...lol
__________________

Totally understand, I put mine up for sale last Tday at the river for $8,500, sold it in a day, was much better than I could have done at home even back then.

 

[Bails]

I want one of those. Looks sweet.

I need to go sit in one to see if 6'4" will fit

 

[srttruck]

I'm 6'4" fit fine in mine. I adjusted the seat all though way back which gained about 2". My knee will hit the dash section that drops down in the center but thats only if I lean it that way.

 

[Cole Trickle]

I'm 6'4" fit fine in mine. I adjusted the seat all though way back which gained about 2". My knee will hit the dash section that drops down in the center but thats only if I lean it that way.

nice...lets see some more pics.

Is that a +6 kit?

 

[scottietwohoty]

I'm 6'4" fit fine in mine. I adjusted the seat all though way back which gained about 2". My knee will hit the dash section that drops down in the center but thats only if I lean it that way.

SICK 4!!! Any more pic's?

 

[srttruck]

nice...lets see some more pics.

Is that a +6 kit?

Yes its a plus 6" it by HCR. With the long travel in conjuction with the wheelbase this has its the best riding SXS in my opinion.
Theres a pic of my custom RZR trailer also. lol
Heres a couple more pics, i'll try to find some better ones.

 

[Cole Trickle]

Yes its a plus 6" it by HCR. With the long travel in conjuction with the wheelbase this has its the best riding SXS in my opinion.
Theres a pic of my custom RZR trailer also. lol
Heres a couple more pics, i'll try to find some better ones.

Nice set up.....:bowdown:

Thats the ultimate family 4 seat cruiser

 

[pronstar]

Damn, that's a bad-ass trailer, too :thumbsup

 

[OutCole'd]

I'm going to go kick my Rhino... Those 4 seaters are bad ass!

 

[Lavey29]

Wow, both of those RZR 4's are bad ass :thumbsup

 

[RiverDave]

That trailer is sick! Who built it? (What does it say on the main rail?)

As well what is painted on the roof of your RZR?

RD

 

[LowRiver2]

Thats the ultimate family 4 seat cruiser

TwistedStich.com

Makes a front bench so that you can make these 6 seaters (kids in middle)

 

[srttruck]

That trailer is sick! Who built it? (What does it say on the main rail?)

As well what is painted on the roof of your RZR?

RD

Thanks! After tring to find a trailer that I thought would be a good fit for the RZR I said to hell with it , I'll build my own. So I built it in the ol garage.

The main rail reads "hooker-up trailers" . I thought I would have to put something on their to get people searchin the web.lol

The roof has a large three digit number and two squares (one red the other blue) to resemble a top view of a cop car.

 

[LowRiver2]

The roof has a large three digit number and two squares (one red the other blue) to resemble a top view of a cop car.

But did you do the wig wag switch for the hi/low beams?

Couple powerflares and some velcro tape and presto: light bar

 

[srttruck]

But did you do the wig wag switch for the hi/low beams?

Couple powerflares and some velcro tape and presto: light bar

I did have a og lightbar but the local authorities did not like it too much, kinda forced to remove it at camp. lol

Man your going to cost me me some $$, those seats look bitchin, and I know there comfy also. :champagne:

 

[LowRiver2]

Hey, you did the same to me with the long travel, heard it makes our 4's into basically sand cars for width, which means little chance of a roll at Glamis:thumbsup

 

[charlyox]

I think trailer says RD SUX.:raisux:

 

[srttruck]

I think trailer says RD SUX.:raisux:

lol. that could happen, I do have a plotter.

 

[LowRiver2]

FWIW, I went with the TS Vortex seats over the Excel. Excel has more wrap around foam, but makes for less space getting in the opening doors. Check both out for size if you go Twisted Stitch.

 

[throttle]

very nice!!!

 

[charlyox]

Damn dude, lookes like you are ready for the Baja 1000.:thumbsup

 

[krackhouse]

Nice!!

 

[riverratmike]

Picked up a RZR4 a month ago and it went straight to SDR
Cage:1 3/4"/opening doors
Twisted Stitch Vortex seats-(heated fronts)/rear bench
Crow 3" 5 points on 4, 2" 4point on center rear bench
ITP 7's/OMF beadlocks
Rigid 30" LED on roof
Rigid 10" LED on front push bar
HID hi low kit on headlights
Center mirror
LED dome light
UMP air canister
Next up: Clutch kit and paddles for Mother G

I think it was you on Kiowa this afternoon around 12:30pm. At lesst that sxs I saw looked just like yours.

 

[LowRiver2]

Nah, not me, have'nt been to Parker since Thanksgiving

No time between Bomb Squad and Asphalt Grinding Biz.


SDR who built mine has done at least 40 RZR 4's since my build, probably one of them

Still completely happy with mine, only negative is finding time to use it

 

[Patyacht]

So since you built your trailer, what do you think are must haves in a trailer. I see alot of them with open sides and yours has closed in sides. I'm just starting my research for an RZR 4 and trailer. Wife has a JCW MINI Cooper that we would tow on occasion also but not both together.

 

[srttruck]

So since you built your trailer, what do you think are must haves in a trailer. I see alot of them with open sides and yours has closed in sides. I'm just starting my research for an RZR 4 and trailer. Wife has a JCW MINI Cooper that we would tow on occasion also but not both together.

I am a fan of having side rails so you can through some loose items on and not worry about it. I built my side rails so that there was 1" of clearance under the doors so they can open easily when loading/unloading. A ramp gate is a no brainer, tie down anchors in the rite spot is also nice. A side step makes it nice to enter/exit the trailer easily. Brakes , big wheels , big fenders , led lighting and being slammed are a must have too. :thumbsup

 

[Patyacht]

Thanks for the trailer info. Just got my new ride when I was down for Desert Storm.

 

[bigmike58]

Looks awesome. My buddy had his cage done by SDR, they make a great cage. I really want one of these but they are just a little small in the leg room department in the front seats, Im 6'4". Did changing the seats to TS give you anymore leg room? I was wondering if there was any way to move the pedals forward 2 or 3 inches, fab new mounts or something.

I'm 6'7" and it's a little cramped in the wifes rzr4 but in my "S" I did the crazywatson dash mod for more knee room and lowered BS sand seats for a couple of inches more legroom..

 

[RiverDave]

Holy shit! What do you have in that thing?

RD

 

[bigmike58]

just a little 2 cyl. 850cc turbo weber built by queen racing in LHC.

 

[LowRiver2]

Did they lift the ban on importing the Weber engines?


Great kit, about $7k after the core trade in, correct?

 

[bigmike58]

Did they lift the ban on importing the Weber engines?


Great kit, about $7k after the core trade in, correct?

pricing is correct... but Chad can't import the motors anymore, if you really want one the best choice is to buy a wrecked fst sled or for more power he has a Z1 conversion now, 160-500hp. I should have one shortly to test at glamis, the 260hp version. The Z1 doesnt have an alternator like the webers so I'm not sure yet on how much lighting we can throw on. I think it has a 500-600w stator like a stock rzr motor.

 

[LowRiver2]

Thanks for the info. and welcome to the board.

 

[RiverDave]

just a little 2 cyl. 850cc turbo weber built by queen racing in LHC.

Mike that's unreal.. Anyway you can shrink that pic in your signiature?
Let me know if you need help.

RD

 

[bigmike58]

Mike that's unreal.. Anyway you can shrink that pic in your signiature?
Let me know if you need help.

RD

sorry...I couldnt see it since I have under 10 posts..bm