WELCOME TO RIVER DAVES PLACE

Recent content by CuttingEdgePropellers

  1. C

    Cutting Edge Propellers Manufacturing And Repair Service

    I'm working on it guys... My Best, Greg
  2. C

    Looking for some prop input

    14 x 19 will work well for you in that boat. If you are not running a stainless prop now, that would be a good upgrade to make for all around performance.
  3. C

    looking to prop for more speed

    Regarding the RPM range of that engine they like to run around 5000 to 5100 with the rev limiter engaging at 5250-5300 or so. If you were to lab that 22 with a tuning of an additional 100 RPM or so that may get you to where you want to be. However 22's are funny critters, they tend to be at...
  4. C

    prop question

    Give me a call regarding tuning that propeller you have. We may be able to pitch it up for you and make it work. Take a look at our propellers as well on our website. My Best, Greg Hittner Cutting Edge Propellers 949-701-0900
  5. C

    prop question

    Hi Dave, The following flo-Torq hubs will convert 2nd generation Bravo style propellers with square hub bores and will fit Johnson Outboards depending upon the specific engine: 835283Q1 835283Q2 835265Q1 835267Q1 835270Q1 My Best, Greg Hittner Cutting Edge Propellers 949-701-0900
  6. C

    Spare Prop

    Hi Chuck, I've been in Lake Havasu for Desrt Storm for a few days for the shootout and I haven't been able to respond. After running the slip numbers on your current setup, your slip calculates at -4%. With that being said, I think your speedo is a bit off. 10 MPH on a water fed speedo is...
  7. C

    new boat / prop package question

    No, I will be leaving after the street party however I'm available by phone 7 days @ 949-701-0900 My Best, Greg Hittner Cutting Edge Propellers 949-701-0900
  8. C

    Prop pitch

    Yes, we do!
  9. C

    Prop pitch

    Thanks for notifying me Dave. The answer to your question is YES, we can re-pitch your propeller up to two pitch sizes up or down and that equates to 400 RPM up or down. That is the Maximum I recommend, any further tends to change the dynamics of the propeller itself and performance will be...
  10. C

    new boat / prop package question

    That Motor will loosen up after a few hours and you may very well pick up that 200 RPM you're looking for. Feel free to give me a call after that and we can discuss further optons for that setup. We'll be at Desert storm for the street party so stop by and say hello! My Bets, Greg Hittner...
  11. C

    Vented props

    Above is correct regarding the ventilation to get on plane easier. As far as the top end numbers, I have seen where ventilated props have helped in the high end MPH but it is not a general rule. If you are running out of prop in the high end, feel free to give me a call or post me here and if...
  12. C

    Prop Talk Forum

    If I can answer any questions for you folks here, Provide service, or maybe just begin some discussions on propellers for your rides, Dave just opened the "Prop Talk" forum. My Best, Greg Hittner Cutting Edge Propellers 949-701-0900
  13. C

    Cutting Edge Propellers is a high performance marine propeller manufacturing and propeller...

    Cutting Edge Propellers is a high performance marine propeller manufacturing and propeller repair company that produces only the finest stainless steel, race labbed propellers. We serve both wholesale and retail clientele. All of our propellers are manufactured 100% in the USA using ONLY virgin...
  14. C

    Gel detail in IE

    I agree Dave, Rick is a master. We handle propeller repairs for him from time to time. As you can imagine with fibergalass damage comes prop damage in many cases. The absolute art I see come out of that shop is unbelievable. It looks dripping wet!
  15. C

    Testing Cuttin Edge props in Havasu

    Really hoping you and Jason hook up out there! Results from two of you are twice as good as one! LOL!:drnkfr My Best, Greg Hittner Cutting Edge Propellers 949-701-0900 www.cuttingedgepropellers.com
Top