Search results

Does it still have the 496?

Hey whats up BOCCO, I run either a 26, 28 or 30 depending on what I'm doing. Yes it has 1.50 gears, still all stock. You are welcome to try any of my props.

Mine has a single assist ram on it, I'll measure it and get back to you. Hey Dave what speeds are you talking here? Mine is dead nuts solid at 90. Once it's aired out on the pad I don't see it chine walking but then again I've only it 90 so far. The prop is beginning to blow out at that...

Since I had a hand in this build, Rob asked me to list out the parts. It's a Beautiful boat, built right. Someone will be getting an awesome boat! I'll start from top to bottom: This build didn't use any used parts, It was all new. The Machine work, assembly and dyno tune was done all in...

New in factory sealed box Rigid Industries 10" SR series combo spot/flood led light bar. Harness/switch/hardware included. Part number#910312, $190 New in factory sealed box pairs of Rigid Industries Dually's both spot and flood led lights. Harness/switch/hardware included, These are the...

Slower than one with a single car motor! Hahahha

I have nothing to gain by posting this, but I went for the first ride with Rob when he got this boat home. Upon first start up you could smell burning oil, When we got back after a short run the transom was black and sooty and it had used over a quart of oil. So unless this thing blew itself...

Complete M-4 setup, Came off a mild 522" BBC that made 1298hp @ 6000 on pump gas. This unit was recently checked out at Procharger and given a clean bill of health. Turn key set up! The video is of this setup on the dyno. Polished M-4 Polished main bracket Polished pulleys Polished intercooler...

For sale - Like new Moonyham 14-71, one piece non stripped rotors, New style 1150 3 circuit Dominators, studs, scoop cover, throttle linkage, Scoop, Pulleys, belt, fuel lines, brand new MSD low profile distributor, etc.. the only thing needed is an intake manifold. I even have a complete big...

A complaint is likely to turn this hard worker into the drive by and waive type. Keep in mind these guys are trying to help you. Every circumstance is different, but I always check to see if anyone, homeowner/criminal, is in the garage prior to going to the door. I would also look at the door...

Spoken like a true San Franciscan, Lol. Kudos to Marcel for sharing his true feelings. Good job bud! Must feel like a weights been lifted. :D

Thank you... I like your signature.. Words I live by.... "People sleep peaceably in their beds at night only because rough men stand ready to do violence on their behalf" -George Orwell

Great DAY!!! Thanks Hammer, It was a pleasure, your welcome to roll with us anytime. It's a single carb pump gas 572, Imco SC -3 shorty. 130+ on the motor 140+ on the bottle:skull http://www.youtube.com/watch?v=8PYuxpkuB_0

We tried to video a nitrous pass, but we had already emptied the bottle on a 141mph run. You can hear the motor pitch change as I get on the button and it goes rich slowing down. Running out of nitrous is one of life's downfalls, lol. I need a blower motor...

Nothing but center pod touching the water!

http://www.youtube.com/watch?v=8PYuxpkuB_0

Whats up man, You are welcome to do an article anytime. As far as 6000rpm?? It's been 3 years since I pulled the 6k limiter chip and replaced it with a 7k and have had no problems(well over 200 hours.) And it's not like I baby this thing either, Every time we are out it see's the limiter...

I put the 150hp jets back in it with the big prop Sunday.... 141.4 mph on the boat GPS, 143 on my phones GPS(updates quicker):thumbup: It got a little hairy at that speed!:skull 7000rpm, 32" Bravo, 1.34 gear!

Awesome work by the way Don! Don also built the Drive on the back of my boat, It's got close to 300 hours on it.