[WTB] BBC

[ChiliPepperGarage]

Looking for a BBC to replace the junked 454 in my jet boat. Would like something around 500HP.

 

[n2otoofast4u]

BP 632 in crate. Complete carb to pan. Dyno sheet says 750ish as I recall. It’s brand new as it comes from them. $11k

 

[ChiliPepperGarage]

BP 632 in crate. Complete carb to pan. Dyno sheet says 750ish as I recall. It’s brand new as it comes from them. $11k

Thanks but don't need that much power and I guess I should mention the budget is about $5K. Don't want to have $20K in a $10K boat!

 

[obnoxious001]

Looking for a BBC to replace the junked 454 in my jet boat. Would like something around 500HP.

I don't have anything ready to go, is your block salvageable?

 

[ChiliPepperGarage]

I don't have anything ready to go, is your block salvageable?

Unfortunately, no. At least I don't think it is worth trying to save it. My brother left it outside and it got water in it so cylinders rusted. It's a shame because the good cylinders are in really good shape so it was a low hour motor. Crank looks good too.
I have a guy that might have a good bare block for me though.
Could you build me a motor in my budget?
I also have an M1 ProCharger for a BBC that I thought about running. I was thinking about a very reliable 400HP build and then run the ProCharger at about 6#'s of boost to get my 500HP. Is that a good plan?

 

[obnoxious001]

Looks like you had a stock 2 bolt, cast crank, small rods and cast pistons. Not sure if it's worth time and effort it would take to get the pistons out, hoping that it would be good after a burn and blast on the block.

500 hp is obtainable with good oval port heads and camshaft combination, no procharger necessary. What cylinder heads do you have?

 

[ChiliPepperGarage]

Heads are stock oval ports but the intake valves are rusted because of the water getting in so probably not salvageable.
I did just talked to a local (northern NV) engine guy and I think I'm going to have him build a motor for me.

 

[ELCHINGONROGERS]

Looking for a BBC to replace the junked 454 in my jet boat. Would like something around 500HP.

buddy got a long block forsale set up for a blower but can be built for carb set up 468 8.1 i think or 9,1 message me if you want more details

 

[guest hs]

I have a steel 502 crank and rectangle port cylinder heads for sale.

 

[AZLineman]

BP 632 in crate. Complete carb to pan. Dyno sheet says 750ish as I recall. It’s brand new as it comes from them. $11k

Thats a deal.

 

[AZLineman]

I have this thats going up for sale. Not what you would want but f it. Lol. Race fuel or E85 good for lightweight jet or car.
418 ci nitrous motor
GM block, 4.280 bore, .009 deck w/o-ring .038 wire
Dart 320 heads 2.300 x 1.880 119cc converted to soft port
Harlan roller rockers, 1.72 ratio
K-motion 1000H valve springs 2.000 setup
Crane stud gurdle
Ross pistons with .040 cut exhaust pocket
Bill Miller aluminum rods, 2.100 rod journal 6.695 length
Childs and Albert o gap rings, .040 plus top ring .028 second
Comp roller cam, with roller lifters, installed with 108 LC
Manley double timing chain with Torington thrust & button roller
Crower crank, 3.625 stroke,
If I recall it was 778HP@7400 on a single dominator. Built for a 300+ shot. $8500 firm

 

[varmit86]

Got a 454 ls6 4 bolt block rectangular port heads see my posting if interested.
Located in Rancho Cucamonga

Sent from my SM-G930P using Tapatalk

 

[ChiliPepperGarage]

Thanks for the replies but I have a local guy building a motor for me. Should be ready by end of the week.

 

[renodaytona]

Thanks for the replies but I have a local guy building a motor for me. Should be ready by end of the week.

Great news! Maybe we will see you out on the water this year yet!

 

[wishiknew]

BP 632 in crate. Complete carb to pan. Dyno sheet says 750ish as I recall. It’s brand new as it comes from them. $11k

Is this the marine or street motor ?? Thanks

 

[ChiliPepperGarage]

Great news! Maybe we will see you out on the water this year yet!

Hope so! The guy is in Fallon so had to drive right past Lohanton to get there and was thinking I'll be out there soon.

My buddy dropped off the jet drive at Performance Speed and Marine in Sparks like 4 years ago. I told him he'd better call them and make sure they still have the jet! The good news is they still have it. Bad news is they haven't touched it despite my buddy already paying them $1400. He told them the motor will be back in the boat in a week and we want to bring it up there so they can reinstall the jet. Guess we'll see what happens.

 

[BUSTI]

I have a steel 502 crank and rectangle port cylinder heads for sale.

What type of shape is your crank in? I may be interested.

 

[guest hs]

I believe it’s std/std needs a polish

 

[wishiknew]

BP 632 in crate. Complete carb to pan. Dyno sheet says 750ish as I recall. It’s brand new as it comes from them. $11k

Is this a marine setup or automotive from them ???

 

[n2otoofast4u]

Is this a marine setup or automotive from them ???

Marine

 

[Good Stuff]

BP 632 in crate. Complete carb to pan. Dyno sheet says 750ish as I recall. It’s brand new as it comes from them. $11k

Is that still available? Got a buddy looking and that would probably a good setup for him. It’s NA I’m guessing?

 

[n2otoofast4u]

Is that still available? Got a buddy looking and that would probably a good setup for him. It’s NA I’m guessing?

It’s as you would buy it from BP. In their crate and all. I have a project slated for it, but if it sells I have a backup plan.