WELCOME TO RIVER DAVES PLACE

Recent content by lbhsbz

  1. lbhsbz

    WTF Just happened?

    I'm out. No desire to be involved in a forum with assholes like the both of you.
  2. lbhsbz

    WTF Just happened?

    He didn't talk shit, you called his wife a cunt. Don't post shit on the internet if you want everyone to mind their own business. I don't talk shit about other peoples wives or kids....there are boundaries, that shouldn't have to be put in fucking writing for decent people.
  3. lbhsbz

    WTF Just happened?

    Way the fuck out of line. Maybe it's time you log off for a bit
  4. lbhsbz

    Tool review monday

    I don’t even have room on the floor lol
  5. lbhsbz

    Tool review monday

    The fact remains, I’ve fixed plenty of cars/boats in the pits (and in a hurry) and on the side of the road with crap tools than I have with the good stuff…and they all got the job done. If you’re not in position where time is money…and sometimes even if you are, the cheap stuff does fine...
  6. lbhsbz

    Tool review monday

    I have….8 I think in my home shop, and one at the river. When I have 100 calipers to tear down, I don’t put everything away after each one is complete….then I might forget while 10 go in the parts washer and then I’m babysitting the blaster full of them…and answering the phone and emails and...
  7. lbhsbz

    Tool review monday

    It's a gift. I have it too.
  8. lbhsbz

    Tool review monday

    An 8mm head goes on a M5 fastener....which is not much bigger than #2 pencil lead...or in this particular case, an M7 bleeder screw with a 2mm hole down the middle of it. How the socket broke before the bleeder, I have no idea. I was using a 4 inch long ratchet lol...and it took almost zero...
  9. lbhsbz

    Tool review monday

    Yeah. I’ve seriously broken more snap on shit than Chinese shit lol. I have a broken 8mm snap on socket here right now. How the fuck does one of those break?
  10. lbhsbz

    Tool review monday

    I have lots of experience with everything from Snap-On to bottom of the barrel junk, and I've found that if you don't abuse them....most work just fine. 1/4" drive stuff ain't gonna break, no matter who made it....but it is tiny and easy to lose, so I mostly now buy Pittsburg or whatever is...
  11. lbhsbz

    Cybertruck to end production

    I watch this guy sometimes when I'm bored...Havasu local who just got a Cybertruck. Say what you want....it's kinda cool though lol.
  12. lbhsbz

    Cybertruck to end production

    Sure it does, it’s just under the tonneau cover. It actually looks more useful than a truck with a tonneau because you can put taller stuff towards the front and still lock it up.
  13. lbhsbz

    Tool review monday

    Just understand that the capacity is limited to about 400lbs now, and make sure to check the air in the tires before you lift ANYTHING. Chinese pneumatic tires like these hold air for about 2 weeks in my experience
  14. lbhsbz

    Some Reasons You May Like AZ over CA

    It’s a required part of the procedure. Typically, if things look OEM…they don’t get much scrutiny, but aftermarket cats are very clear, and rules state they must identify and verify the EO number etched into it to properly perform the inspection. It’s a gamble…you could spend $1000 on Fed...
  15. lbhsbz

    Some Reasons You May Like AZ over CA

    AP and Walker both make garbage parts IMO. Magnaflow is decent, but check OE prices at some online dealers….for my 4runner, there was only about 10% difference. Both of those part numbers are for the rear (non-monitored) cats, and they are not CA legal…they will fail the visual. Also, the...
Back
Top