For those of you that like Jeeps

[Jonas Grumby]

Showed a little love to my. Jk today. Dynatrac pro rock 44 , reid racing knuckles, RPM 1 ton aluminum flipped Tie bar/drag link.
If your

 

[mjc]

Showed a little love to my. Jk today. Dynatrac pro rock 44 , reid racing knuckles, RPM 1 ton aluminum flipped Tie bar/drag link.
If your looking for a gently used high pinion dana 30 front, with knuckles, tie bar, drag link, I only have 20k on the Jeep. View attachment 1050732 View attachment 1050733 View attachment 1050734 View attachment 1050735

Maybe. What gears are in it? Any airlocker?

 

[Jonas Grumby]

Maybe. What gears are in it? Any airlocker?

3.21 out of a sport, no locker

 

[Nanu/Nanu]

Awesome stuff man! I would like to do something similar in my jk sport too!

 

[havasujeeper]

Lookin' good!

 

[Jonas Grumby]

Well lesson learned. Reid racing knuckles won’t work with pro rock 44 without modification.

so stockers going back on.

for sale brand new Reid racing knuckles, 0 miles. Where put on, and takin off. Cost me $260 each.My loss your gain. $425.00 in havasu.

 

[Nanu/Nanu]

What was it about these knuckles that won't work just curious?

 

[sintax]

Well lesson learned. Reid racing knuckles won’t work with pro rock 44 without modification.

so stockers going back on.

for sale brand new Reid racing knuckles, 0 miles. Where put on, and takin off. Cost me $260 each.My loss your gain. $425.00 in havasu.

wheres the issue?

on the inner C's?

 

[Jonas Grumby]

wheres the issue?

on the inner C's?

Look at the drag link. The Reid knuckles are 1” higher, puts the drag link against the steering stabilizer bracket

 

[sintax]

Look at the drag link. The Reid knuckles are 1” higher, puts the drag link against the steering stabilizer bracket

Ah I can see it now in the first picture. Hard to tell from the angle of the pic exactly what sort of interference you have.

That’s the issue when you start with the bolt ons, tweaks are inevitable.

 

[Nanu/Nanu]

Ahhh! Dang it man that's a real drag!

Where did you order your dynatrac from and was it difficult?

Was there much to the swap aside from the steps needed to actually swap the axle?

This is a cool project! Keep up the good work!

 

[Jonas Grumby]

Ahhh! Dang it man that's a real drag!

Where did you order your dynatrac from and was it difficult?

Was there much to the swap aside from the steps needed to actually swap the axle?

This is a cool project! Keep up the good work!

I bought from dynatrac, , 12 week wait, then shipped to my house.

 

[Jonas Grumby]

Now I need to find someone in town that knows how to setup my rear end, I have new matching gears, a ARB and chromolly axles to get installed. I already ran the air line.

So I’m 513 with ARB up front and 321 in the rear. I left the front driveshaft off. Don’t need a ooppps, moment.

 

[mjc]

Now I need to find someone in town that knows how to setup my rear end, I have new matching gears, a ARB and chromolly axles to get installed. I already ran the air line.

So I’m 513 with ARB up front and 321 in the rear. I left the front driveshaft off. Don’t need a ooppps, moment.

check with Gooley's Garage for that